Changes

<tr><th><p class="s13">Merkmale</p></th><th><p class="s13">Form B Form C</p><p class="s13">Rundkopf Trapezkopf bombiert Trapezkopf, flach </p></th><th><p class="s13">Prüfmittelvorschlag</p><p class="s13"></p></th></tr><tr><td><p class="s13">a) Kopfdurchmesser</p><p class="s13">d<span class="s14">₁ </span>[mm]</p></td><td><p class="s13">Bei optischer Messung ohne Berücksichtigung des Eckenradius R<span class="s14">₃ </span><u>+</u> 0.1</p></td><td><p class="s13">Projektor,</p><p class="s13">Messmikroskop</p></td></tr><tr><td><p class="s13">b) Kopfhöhe</p><p class="s13">k [mm]</p></td><td><p class="s13">+ 0.1</p></td><td><p class="s13">Mikrometer,</p><p class="s13">Messuhr</p></td></tr><tr><td><p class="s13">c) Schaftdurchmesser</p><p class="s13">d<span class="s14">₂ </span>[mm]</p></td><td><p class="s13">Abweichung von Rundheit und konischer Form des Schaftes</p><p class="s13">nur innerhalb der zulässigen Durchmessertoleranz d<span class="s14">₂ </span> <u>&lt;</u> 1.5 - 0.08</p><p class="s13">d<span class="s14">₂ </span>&gt; 1.5 - 0.1</p></td><td><p class="s13">Mikrometer</p></td></tr><tr><td><p class="s13">d) Schaftlänge </p><p class="s13">[mm]</p></td><td><p class="s13">+ 0.15</p></td><td><p class="s13">Mikrometer, Messuhr, Projektor</p></td></tr><tr><td><p class="s13">e) Radius Mitte</p><p class="s13">Kontaktfläche</p><p class="s13">R<span class="s14">₁ </span>[mm]</p></td><td><p class="s13">Form B:<u>+</u> 10%, aber nicht unter +<span class="s13"> 0.5 mm</span></p><p class="s13">Form C: Zulässige Planheitsabweichung:</p><p class="s13"> konvex: innerhalb der Kopfhöhentoleranz</p><p class="s13"> konkav: 0.005 d<span class="s14">1</span></p></td><td><p class="s13">Projektor </p><p class="s13">Projektorschablone, Radiuslehre, Messuhr, Projektor</p></td></tr><tr><td><p class="s13">f) Radius at edge</p><p class="s13">of contact surfaceRand Kontaktfläche </p><p class="s13">R<span class="s14">₂ </span>[mm]</p></td><td><p class="s13">per Per DIN 46240: Form B and und C max. 0.,5 without ohne DIN:max. 1</p></td><td><p class="s13">Profile templateProfilschablone, Projektor,</p><p class="s13">Comparator, Radius gageRadiuslehre</p></td></tr><tr><td><p class="s13">g) Radii</p><p class="s13">R<span class="s14">₃ </span>and R<span class="s14">₅ </span>[mm]</p></td><td><p class="s13">Sligth rounding allowed</p></td><td><p class="s13">Comparator</p></td></tr><tr><td><p class="s13">h) Transition radius</p><p class="s13">head underside to shank R<span class="s14">₄ </span>[mm]</p></td><td><p class="s13">d<span class="s14">₂ </span><u>&lt;</u> 2 R<span class="s14">₄ </span><u>&lt;</u> 0.08 d<span class="s14">₂ </span>&gt; 2 R<span class="s14">₄ </span><u>&lt;</u> 0.1 d<span class="s14">₂ </span>&gt; 3 R<span class="s14">₄ </span><u>&lt;</u> 0.2</p></td><td><p class="s13">Comparator, if in doubt: micro-section</p></td></tr><tr><td><p class="s13">i) Allowed deviation from cylindrical shape</p></td><td><p class="s13">d<span class="s14">₁ </span> <u>&lt;</u> 4 up to 7°30’ + 2°30’</p><p class="s13">d<span class="s14">₁ </span>&gt; 4 up to 10° + 5°</p></td><td><p class="s13">Comparator, Measu- ring microscope, if in doubt: microsection</p></td></tr><tr><td><p class="s13">k) Concentricity bet-</p><p class="s13">ween head and shank center line [mm]</p></td><td><p class="s13">5% of d<span class="s14">₁</span></p></td><td><p class="s13">Comparator,</p><p class="s13">Measuring microscope, Special turn fixture</p></td></tr><tr><td><p class="s13">l) Contact layer</p><p class="s13">thickness [mm]</p></td><td><p class="s13">In center area of 0.5 d<span class="s14">₁ </span>s<u>&gt;</u> nominal thickness</p><p class="s13">Remaining head area must be covered</p></td><td><p class="s13">Measuring micros- cope, Microsection</p></td></tr></table>