Changes

Jump to: navigation, search

Silver Based Materials

5,945 bytes added, 17:17, 24 September 2014
no edit summary
Pure silver (also called fine silver) exhibits the highest electrical and thermal conductivity of all metals. It is also resistant against oxidation. Major disadvantages are its low mechanical wear resistance, the low softening temperature, and especially its strong affinity to sulfur and sulfur compounds. In the presence of sulfur and sulfur containing compounds brownish to black silver sulfide layer are formed on its surface. These can cause increased contact resistance or even total failure of a switching device if they are not mechanically, electrically, or thermally destroyed. Other weaknesses of silver contacts are the tendency to weld under the influence of over-currents and the low resistance against material transfer when switching DC loads. In humid environments and under the influence of an electrical field silver can creep (silver migration) and cause electrical shorting between adjacent current paths.
<xr id="tab:Overview of the Most Widely Used Silver GradesOverview_of_the_Most_Widely_Used_Silver_Grades"/> <!--(Table 2.11) --> shows the typically available quality grades of silver. In certain economic areas, i.e. China, there are additional grades with varying amounts of impurities available on the market. In powder form silver is used for a wide variety of silver based composite contact materials. Different manufacturing processes result in different grades of Ag powder as shown in <xr id="tab:tab2.12Quality_Criteria_of_Differently_Manufactured_Silver_Powders"/> <!--Table 2.12-->. additional properties of silver powders and their usage are described in [[ Precious Metal Powders and Preparations#Precious_Metal_Powders|Precious Metal Powders ]] und [[Precious_Metal_Powders_and_Preparations|Tab. 8Table Different Types of Silver Powders.1]] <!--(Tab. 8.1.) -->
Semi-finished silver materials can easily be warm or cold formed and can be clad to the usual base materials. For attachment of silver to contact carrier materials welding of wire or profile cut-offs and brazing are most widely applied. Besides these mechanical processes such as wire insertion (wire staking) and the riveting (staking) of solid or composite contact rivets are used in the manufacture of contact components.
Contacts made from fine silver are applied in various electrical switching devices such as relays, pushbuttons, appliance and control switches for
currents < 2 A <xr id="tab:tab2.16Application Examples and Forms of Supply for Silver and Silver Alloys"/> <!--(Table 2.16)-->. Electroplated silver coatings are widely used to reduce the contact resistance and improve the brazing behavior of other contact materials and components.
 <figtable id="tab:Overview of the Most Widely Used Silver GradesOverview_of_the_Most_Widely_Used_Silver_Grades"><caption>'''<!--Table 2.11: -->Overview of the Most Widely Used Silver Grades'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Designation</p></th><th><p class="s12">Composition minimum Ag [wt%]</p></th><th><p class="s12">Impurities</p><p class="s12">[ppm]</p></th><th><p class="s12">Notes on Usage</p></th></tr><tr><td><p class="s12">Spectroscopically</p><p class="s12">Pure Ag</p></td><td><p class="s11">99.999</p></td><td><p class="s11">Cu &lt; 3</p><p class="s11">Zn &lt; 1</p><p class="s11">Si &lt; 1</p><p class="s11">Ca &lt; 2</p><p class="s11">Fe &lt; 1</p><p class="s11">Mg &lt; 1</p><p class="s11">Cd &lt; 1</p></td><td><p class="s12">Sheets, strips, rods, wires for electronic applications</p></td></tr><tr><td><p class="s12">High Purity Ag, oxygen-free</p></td><td><p class="s11">99.995</p></td><td><p class="s11">Cu &lt; 30</p><p class="s11">Zn &lt; 2</p><p class="s11">Si &lt; 5</p><p class="s11">Ca &lt; 10</p><p class="s11">Fe &lt; 3</p><p class="s11">Mg &lt; 5</p><p class="s11">Cd &lt; 3</p></td><td><p class="s12">Ingots, bars, granulate for alloying</p><p class="s12">purposes</p></td></tr></table>
<figtable id="tab:tab2.12Quality_Criteria_of_Differently_Manufactured_Silver_Powders"><caption>'''<!--Table 2.12: -->Quality Criteria of Differently Manufactured Silver Powders'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
<xr id="fig:Strain hardening of Ag bei cold working"/> <!--Fig. 2.45: --> Strain hardening of Ag 99.95 by cold working
<xr id="fig:Softening of Ag after annealing after different degrees"/> <!--Fig. 2.46: --> Softening of Ag 99.95 after annealing for 1 hr after different degrees of strain hardening
===Silver Alloys===
To improve the physical and contact properties of fine silver melt-metallurgical produced silver alloys are used <xr id="tab:Physical Properties of Silver and Silver Alloys"/> <!--(Table 2.13)-->. By adding metal components the mechanical properties such as hardness and tensile strength as well as typical contact properties such as erosion resistance, and resistance against material transfer in DC circuits are increased <xr id="tab:tab2.14Mechanical Properties of Silver and Silver Alloys"/> <!--(Table 2.14)-->. On the other hand however, other properties such as electrical conductivity and chemical corrosion resistance can be negatively impacted by alloying <xr id="fig:Influence of 1 10 atom of different alloying metals"/> <!--(Fig. 2.47) --> and <xr id="fig:Electrical resistivity p of AgCu alloys"/> <!--(Fig. 2.48)-->.
<figtable id="tab:Physical Properties of Silver and Silver Alloys">
<caption>'''<!--Table 2.13: -->Physical Properties of Silver and Silver Alloys'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
</figtable>
<xr id="fig:Influence of 1 10 atom of different alloying metals"/> <!--Fig. 2.47: --> Influence of 1-10 atom% of different alloying metals on the electrical resistivity of silver
<xr id="fig:Electrical resistivity p of AgCu alloys"/> <!--Fig. 2.48: --> Electrical resistivity p of AgCu alloys
<div class="multiple-images">
====Fine-Grain Silver====
Fine-Grain Silver (ARGODUR-Spezial) is defined as a silver alloy with an addition of 0.15 wt% of Nickel. Silver and nickel are not soluble in each other in solid form. In liquid silver only a small amount of nickel is soluble as the phase diagram <xr id="fig:Phase diagram of silver nickel"/> <!--(Fig. 2.51) --> illustrates. During solidification of the melt this nickel addition gets finely dispersed in the silver matrix and eliminates the pronounce coarse grain growth after prolonged influence of elevated temperatures <xr id="fig:Coarse grain micro structure of Ag"/> <!--(Fig. 2.49) --> and <xr id="fig:Fine grain microstructure of AgNiO"/> <!--(Fig. 2.50)-->.
<div class="multiple-images">
<div class="clear"></div>
Fine-grain silver has almost the same chemical corrosion resistance as fine silver. Compared to pure silver it exhibits a slightly increased hardness andtensile strength <xr id="tab:Mechanical Properties of Silver and Silver Alloys"/> <!--(Table 2.14)-->. The electrical conductivity is just slightly decreased by this low nickel addition. Because of its significantly improved contact properties fine grain silver has replaced pure silver in many applications.
====Hard-Silver Alloys====
Using copper as an alloying component increases the mechanical stability of silver significantly. The most important among the binary AgCu alloys is that of AgCu3, known in europe also under the name of hard-silver. This material still has a chemical corrosion resistance close to that of fine silver. In comparison to pure silver and fine-grain silver AgCu3 exhibits increased mechanical strength as well as higher arc erosion resistance and mechanical wear resistance <xr id="tab:Mechanical Properties of Silver and Silver Alloys"/> <!--(Table 2.14)-->.
<figtable id="tab:Mechanical Properties of Silver and Silver Alloys">
<caption>'''<!--Table 2.14: -->Mechanical Properties of Silver and Silver Alloys'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material/</p><p class="s12">DODUCO-Designation</p></th><th><p class="s12">Hardness</p><p class="s12">Condition</p></th><th><p class="s12">Tensile Strength</p><p class="s12">R<span class="s31">m </span>[MPa]</p></th><th><p class="s12">Elongation A [%] min.</p></th><th><p class="s12">Vickers Hardness</p><p class="s12">HV 10</p></th></tr><tr><td><p class="s12">Ag</p></td><td><p class="s12">R 200</p><p class="s12">R 250</p><p class="s12">R 300</p><p class="s12">R 360</p></td><td><p class="s12">200 - 250</p><p class="s12">250 - 300</p><p class="s12">300 - 360</p><p class="s12">&gt; 360</p></td><td><p class="s12">30</p><p class="s12">8</p><p class="s12">3</p><p class="s12">2</p></td><td><p class="s12">30</p><p class="s12">60</p><p class="s12">80</p><p class="s12">90</p></td></tr><tr><td><p class="s12">AgNi 0,15</p><p class="s12">ARGODUR Special</p></td><td><p class="s12">R 220</p><p class="s12">R 270</p><p class="s12">R 320</p><p class="s12">R 360</p></td><td><p class="s12">220 - 270</p><p class="s12">270 - 320</p><p class="s12">320 - 360</p><p class="s12">&gt; 360</p></td><td><p class="s12">25</p><p class="s12">6</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">40</p><p class="s12">70</p><p class="s12">85</p><p class="s12">100</p></td></tr><tr><td><p class="s12">AgCu3</p></td><td><p class="s12">R 250</p><p class="s12">R 330</p><p class="s12">R 400</p><p class="s12">R 470</p></td><td><p class="s12">250 - 330</p><p class="s12">330 - 400</p><p class="s12">400 - 470</p><p class="s12">&gt; 470</p></td><td><p class="s12">25</p><p class="s12">4</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">45</p><p class="s12">90</p><p class="s12">115</p><p class="s12">120</p></td></tr><tr><td><p class="s12">AgCu5</p></td><td><p class="s12">R 270</p><p class="s12">R 350</p><p class="s12">R 460</p><p class="s12">R 550</p></td><td><p class="s12">270 - 350</p><p class="s12">350 - 460</p><p class="s12">460 - 550</p><p class="s12">&gt; 550</p></td><td><p class="s12">20</p><p class="s12">4</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">55</p><p class="s12">90</p><p class="s12">115</p><p class="s12">135</p></td></tr><tr><td><p class="s12">AgCu10</p></td><td><p class="s12">R 280</p><p class="s12">R 370</p><p class="s12">R 470</p><p class="s12">R 570</p></td><td><p class="s12">280 - 370</p><p class="s12">370 - 470</p><p class="s12">470 - 570</p><p class="s12">&gt; 570</p></td><td><p class="s12">15</p><p class="s12">3</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">60</p><p class="s12">95</p><p class="s12">130</p><p class="s12">150</p></td></tr><tr><td><p class="s12">AgCu28</p></td><td><p class="s12">R 300</p><p class="s12">R 380</p><p class="s12">R 500</p><p class="s12">R 650</p></td><td><p class="s12">300 - 380</p><p class="s12">380 - 500</p><p class="s12">500 - 650</p><p class="s12">&gt; 650</p></td><td><p class="s12">10</p><p class="s12">3</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">90</p><p class="s12">120</p><p class="s12">140</p><p class="s12">160</p></td></tr><tr><td><p class="s12">Ag98CuNi</p><p class="s12">ARGODUR 27</p></td><td><p class="s12">R 250</p><p class="s12">R 310</p><p class="s12">R 400</p><p class="s12">R 450</p></td><td><p class="s12">250 - 310</p><p class="s12">310 - 400</p><p class="s12">400 - 450</p><p class="s12">&gt; 450</p></td><td><p class="s12">20</p><p class="s12">5</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">50</p><p class="s12">85</p><p class="s12">110</p><p class="s12">120</p></td></tr><tr><td><p class="s12">AgCu24,5Ni0,5</p></td><td><p class="s12">R 300</p><p class="s12">R 600</p></td><td><p class="s12">300 - 380</p><p class="s12">&gt; 600</p></td><td><p class="s12">10</p><p class="s12">1</p></td><td><p class="s12">105</p><p class="s12">180</p></td></tr><tr><td><p class="s12">AgCd10</p></td><td><p class="s12">R 200</p><p class="s12">R 280</p><p class="s12">R 400</p><p class="s12">R 450</p></td><td><p class="s12">200 - 280</p><p class="s12">280 - 400</p><p class="s12">400 - 450</p><p class="s12">&gt; 450</p></td><td><p class="s12">15</p><p class="s12">3</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">36</p><p class="s12">75</p><p class="s12">100</p><p class="s12">115</p></td></tr><tr><td><p class="s12">Ag99,5NiMg</p><p class="s12">ARGODUR 32</p><p class="s12">Not heat treated</p></td><td><p class="s12">R 220</p><p class="s12">R 260</p><p class="s12">R 310</p><p class="s12">R 360</p></td><td><p class="s12">220</p><p class="s12">260</p><p class="s12">310</p><p class="s12">360</p></td><td><p class="s12">25</p><p class="s12">5</p><p class="s12">2</p><p class="s12">1</p></td><td><p class="s12">40</p><p class="s12">70</p><p class="s12">85</p><p class="s12">100</p></td></tr><tr><td><p class="s12">ARGODUR 32 Heat treated</p></td><td><p class="s12">R 400</p></td><td><p class="s12">400</p></td><td><p class="s12">2</p></td><td><p class="s12">130-170</p></td></tr></table>
Increasing the Cu content further also increases the mechanical strength of AgCu alloys and improves arc erosion resistance and resistance against material transfer while at the same time however the tendency to oxide formation becomes detrimental. This causes during switching under arcing conditions an increase in contact resistance with rising numbers of operation. In special applications where highest mechanical strength is recommended and a reduced chemical resistance can be tolerated, the eutectic AgCu alloy with 28 wt% of copper <xr id="fig:Phase diagram of silver copper"/> <!--(Fig. 2.52) --> is used. AgCu10 also known as coin silver has been replaced in many applications by composite silver-based materials while sterling silver (AgCu7.5) has never extended its important usage from decorative table wear and jewelry to industrial applications in electrical contacts.
Besides these binary alloys, ternary AgCuNi alloys are used in electrical contact applications. From this group the material ARGODUR 27, an alloy of 98 wt% Ag with a 2 wt% Cu and nickel addition has found practical importance close to that of AgCu3. This material is characterized by high resistance to oxidation and low tendency to re-crystallization during exposure to high temperatures. Besides high mechanical stability this AgCuNi alloy also exhibits a strong resistance against arc erosion. Because of its high resistance against material transfer the alloy AgCu24.5Ni0.5 has been used in the automotive industry for an extended time in the North American market. Caused by miniaturization and the related reduction in available contact forces in relays and switches this material has been replaced widely because of its tendency to oxide formation.
The attachment methods used for the hard silver materials are mostly close to those applied for fine silver and fine grain silver.
Hard-silver alloys are widely used for switching applications in the information and energy technology for currents up to 10 A, in special cases also for higher current ranges <xr id="tab:Application Examples and Forms of Supply for Silver and Silver Alloys"/> <!--(Table 2.16)-->.
Dispersion hardened alloys of silver with 0.5 wt% MgO and NiO (ARGODUR 32) are produced by internal oxidation. While the melt-metallurgical alloy is easy to cold-work and form the material becomes very hard and brittle after dispersion hardening. Compared to fine silver and hard-silver this material has a greatly improved temperature stability and can be exposed to brazing temperatures up to 800°C without decreasing its hardness and tensile strength.
<xr id="fig:Phase diagram of silver copper"/> <!--Fig. 2.52: --> Phase diagram of silver-copper
<xr id="fig:Phase diagram of silver cadmium"/> <!--Fig. 2.53: --> Phase diagram of silver-cadmium
<xr id="fig:Strain hardening of AgCu3 by cold working"/> <!--Fig. 2.54: --> Strain hardening of AgCu3 by cold working
<xr id="fig:Softening of AgCu3 after annealing"/> <!--Fig. 2.55: --> Softening of AgCu3 after annealing for 1 hr after 80% cold working
<xr id="fig:Strain hardening of AgCu5 by cold working"/> <!--Fig. 2.56: --> Strain hardening of AgCu5 by cold working
<xr id="fig:Softening of AgCu5 after annealing"/> <!--Fig. 2.57: --> Softening of AgCu5 after annealing for 1 hr after 80% cold working
<xr id="fig:Strain hardening of AgCu 10 by cold working"/> <!--Fig. 2.58: --> Strain hardening of AgCu 10 by cold working
<xr id="fig:Softening of AgCu10 after annealing"/> <!--Fig. 2.59: --> Softening of AgCu10 after annealing for 1 hr after 80% cold working
<xr id="fig:Strain hardening of AgCu28 by cold working"/> <!--Fig. 2.60: --> Strain hardening of AgCu28 by cold working
<xr id="fig:Softening of AgCu28 after annealing"/> <!--Fig. 2.61: --> Softening of AgCu28 after annealing for 1 hr after 80% cold working
<xr id="fig:Strain hardening of AgNiO15 by cold working"/> <!--Fig. 2.62: --> Strain hardening of AgNi0.15 by cold working
<xr id="fig:Softening of AgNiO15 after annealing"/> <!--Fig. 2.63: --> Softening of AgNi0.15 after annealing for 1 hr after 80% cold working
<xr id="fig:Strain hardening of ARGODUR 27"/> <!--Fig. 2.64: --> Strain hardening of ARGODUR 27 by cold working
<xr id="fig:Softening of ARGODUR 27 after annealing"/> <!--Fig. 2.65: --> Softening of ARGODUR 27 after annealing for 1 hr after 80% cold working
<div class="multiple-images">
<figtable id="tab:Contact and Switching Properties of Silver and Silver Alloys"><caption>'''<!--Table 2.15: -->Contact and Switching Properties of Silver and Silver Alloys'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
|Good formability, good brazing and welding properties
|}
</figtable>
<figtable id="tab:Application Examples and Forms of Supply for Silver and Silver Alloys">
<caption>'''<!--Table 2.16: -->Application Examples and Forms of Supply for Silver and Silver Alloys'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
|-
|Ag<br />AgNi0,15<br />ARGODUR-Spezial<br />AgCu3<br />AgNi98NiCu2<br />ARGODUR 27<br />AgCu24,5Ni0,5
|Relays,<br />Micro switches,<br />Auxiliary current switches,<br />Control circuit devices,<br />Appliance switches,<br />Wiring devices (< &le; 20A),<br />Main switches
|'''Semi-finished Materials:''' <br />Strips, wires, contact profiles, clad contact strips, toplay profiles, seam- welded strips<br />'''Contact Parts:'''<br />Contact tips, solid and composite rivets, weld buttons; clad, welded and riveted contact parts
|-
====Silver-Palladium Alloys====
The addition of 30 wt% Pd increases the mechanical properties as well as the resistance of silver against the influence of sulfur and sulfur containing compounds significantly <xr id="tab:Physical Properties of Silver-Palladium Alloys"/> <!--(Tab 2.17) --> and <xr id="tab:Mechanical Properties of Silver-Palladium Alloys"/> <!--(Tab.2.18)-->. Alloys with 40-60 wt% Pd have an even higher resistance against silver sulfide formation. At these percentage ranges however the catalytic properties of palladium can influence the contact resistance behavior negatively. The formability also decreases with increasing Pd contents.
AgPd alloys are hard, arc erosion resistant, and have a lower tendency towards material transfer under DC loads <xr id="tab:Contact and Switching Properties of Silver-Palladium Alloys"/> <!--(Table 2.19)-->. On the other hand the electrical conductivity is decreased at higher Pd contents. The ternary alloy AgPd30Cu5 has an even higher hardness which makes it suitable for use in sliding contact systems.
AgPd alloys are mostly used in relays for the switching of medium to higher loads (> 60V, > 2A) as shown in <xr id="tab:Application Examples and Forms of Suppl for Silver-Palladium Alloys"/> <!--(Table 2.20)-->. Because of the high palladium price these formerly solid contacts have been widely replaced by multi-layer designs such as AgNi0.15 or AgNi10 with a thin Au surface layer. A broader field of application for AgPd alloys remains in the wear resistant sliding contact systems.
<xr id="fig:Phase diagram of silver palladium"/> <!--Fig. 2.66: --> Phase diagram of silver-palladium
<xr id="fig:Strain hardening of AgPd30 by cold working"/> <!--Fig. 2.67: --> Strain hardening of AgPd30 by cold working
<xr id="fig:Strain hardening of AgPd50 by cold working"/> <!--Fig. 2.68: --> Strain hardening of AgPd50 by cold working
<xr id="fig:Strain hardening of AgPd30Cu5 by cold working"/> <!--Fig. 2.69: --> Strain hardening of AgPd30Cu5 by cold working
<xr id="fig:Softening of AgPd30 AgPd50 AgPd30Cu5"/> <!--Fig. 2.70: --> Softening of AgPd30, AgPd50, and AgPd30Cu5 after annealing of 1 hr after 80% cold working
<div class="multiple-images">
<figtable id="tab:Physical Properties of Silver-Palladium Alloys">
<caption>'''<!--Table 2.17: --> Physical Properties of Silver-Palladium Alloys'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
!Electrical<br />Conductivity<br />[MS/m]
!Thermal<br />Conductivity<br />[W/m·K]
!Temp. Coefficient of<br />the Electr.Resistance<br />[10<sup>-3</sup>/K]
|-
|AgPd30
<figtable id="tab:Mechanical Properties of Silver-Palladium Alloys">
<caption>'''<!--Table 2.18: -->Mechanical Properties of Silver-Palladium Alloys'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material</p></th><th><p class="s12">Hardness</p><p class="s12">Condition</p></th><th><p class="s12">Tensile Strength</p><p class="s12">R<span class="s31"><sub>m</sub></span>[MPa]</p></th><th><p class="s12">Elongation A</p><p class="s12">[%]min.</p></th><th><p class="s12">Vickers Hardness</p><p class="s12">HV</p></th></tr><tr><td><p class="s12">AgPd30</p></td><td><p class="s12">R 320</p><p class="s12">R 570</p></td><td><p class="s12">320</p><p class="s12">570</p></td><td><p class="s12">38</p><p class="s12">3</p></td><td><p class="s12">65</p><p class="s12">145</p></td></tr><tr><td><p class="s12">AgPd40</p></td><td><p class="s12">R 350</p><p class="s12">R 630</p></td><td><p class="s12">350</p><p class="s12">630</p></td><td><p class="s12">38</p><p class="s12">2</p></td><td><p class="s12">72</p><p class="s12">165</p></td></tr><tr><td><p class="s12">AgPd50</p></td><td><p class="s12">R 340</p><p class="s12">R 630</p></td><td><p class="s12">340</p><p class="s12">630</p></td><td><p class="s12">35</p><p class="s12">2</p></td><td><p class="s12">78</p><p class="s12">185</p></td></tr><tr><td><p class="s12">AgPd60</p></td><td><p class="s12">R 430</p><p class="s12">R 700</p></td><td><p class="s12">430</p><p class="s12">700</p></td><td><p class="s12">30</p><p class="s12">2</p></td><td><p class="s12">85</p><p class="s12">195</p></td></tr><tr><td><p class="s12">AgPd30Cu5</p></td><td><p class="s12">R 410</p><p class="s12">R 620</p></td><td><p class="s12">410</p><p class="s12">620</p></td><td><p class="s12">40</p><p class="s12">2</p></td><td><p class="s12">90</p><p class="s12">190</p></td></tr></table>
<figtable id="tab:Contact and Switching Properties of Silver-Palladium Alloys">
<caption>'''<!--Table 2.19: -->Contact and Switching Properties of Silver-Palladium Alloys''</caption>'
{| class="twocolortable" style="text-align: left; font-size: 12px"
<figtable id="tab:Application Examples and Forms of Suppl for Silver-Palladium Alloys">
<caption>'''<!--Table 2.20: -->Application Examples and Forms of Suppl for Silver-Palladium Alloys'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material</p></th><th><p class="s12">Application Examples</p></th><th><p class="s12">Form of Supply</p></th></tr><tr><td><p class="s12">AgPd 30-60</p></td><td><p class="s12">Switches, relays, push-buttons,</p><p class="s12">connectors, sliding contacts</p></td><td><p class="s12">'''Semi-finished Materials:'''</p><p class="s12">Wires, micro profiles (weld tapes), clad</p><p class="s12">contact strips, seam-welded strips</p><p class="s12">'''Contact Parts:'''</p><p class="s12">Solid and composite rivets, weld buttons;</p><p class="s12">clad and welded contact parts, stamped parts</p></td></tr><tr><td><p class="s12">AgPd30Cu5</p></td><td><p class="s12">Sliding contacts, slider tracks</p></td><td><p class="s12">Wire-formed parts, contact springs, solid</p><p class="s12">and clad stamped parts</p></td></tr></table>
</figtable>
====Silver-Nickel (SINIDUR) Materials====
Since silver and nickel are not soluble in each other in solid form and in the liquid phase have only very limited solubility silver nickel composite materials with higher Ni contents can only be produced by powder metallurgy. During extrusion of sintered Ag/Ni billets into wires, strips and rods the Ni particles embedded in the Ag matrix are stretched and oriented in the microstructure into a pronounced fiber structure <xr id="fig:Micro structure of AgNi9010"/> <!--(Fig. 2.75) --> and <xr id="fig:Micro structure of AgNi 8020"/> <!--(Fig. 2.76)-->
The high density produced during hot extrusion aids the arc erosion resistance of these materials <xr id="tab:Physical Properties of Silver-Nickel (SINIDUR) Materials"/> <!--(Tab 2.21)-->. The typical application of Ag/Ni contact materials is in devices for switching currents of up to 100A <xr id="tab:Application Examples and Forms of Supply for Silver-Nickel (SINIDUR) Materials"/> <!--(Table 2.24)-->. In this range they are significantly more erosion resistant than silver or silver alloys. In addition they exhibit with nickel contents < 20 wt% a low and over their operational lifetime consistent contact resistance and good arc moving properties. In DC applications Ag/Ni materials exhibit a relatively low tendency of material transfer distributed evenly over the contact surfaces <xr id="tab:Contact and Switching Properties of Silver-Nickel (SINIDUR) Materials"/> <!--(Table 2.23)-->.
Typically Ag/Ni (SINIDUR) materials are usually produced with contents of 10-40 wt% Ni. The most widely used materials SINIDUR 10 and SINIDUR 20- and also SINIDUR 15, mostly used in north america-, are easily formable and applied by cladding <xr id="fig:Strain hardening of AgNi9010 by cold working"/> <!--(Fig. 2.71) --> <xr id="fig:Softening of AgNi9010 after annealing"/> <!--(Fig. 2.72) --> <xr id="fig:Strain hardening of AgNi8020"/> <!--(Fig. 2.73) --> <xr id="fig:Softening of AgNi8020 after annealing"/> <!--(Fig. 2.74)-->. They can be, without any additional welding aids, economically welded and brazed to the commonly used contact carrier materials.
The (SINIDUR) materials with nickel contents of 30 and 40 wt% are used in switching devices requiring a higher arc erosion resistance and where increases in contact resistance can be compensated through higher contact forces.
The most important applications for Ag/Ni contact materials are typically in relays, wiring devices, appliance switches, thermostatic controls, auxiliary switches, and small contactors with nominal currents > 20A <xr id="tab:Application Examples and Forms of Supply for Silver-Nickel (SINIDUR) Materials"/> <!--(Table 2.24)-->.
<figtable id="tab:Physical Properties of Silver-Nickel (SINIDUR) Materials">
<caption>'''<!--Table 2.21: -->Physical Properties of Silver-Nickel (SINIDUR) Materials'''</caption>
<table class="twocolortable">
<tr><th>Material/DODUCO</th><th>Silver Content</th><th>Density</th><th>Melting Point</th><th>ElectricalResistivity<i>p</i></th><th colspan="2">Electrical Resistivity (soft)</th></tr>
<figtable id="tab:tab2.22">
<caption>'''<!-- Table 2.22: -->Mechanical Properties of Silver-Nickel (SINIDUR) Materials'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
<xr id="fig:Strain hardening of AgNi9010 by cold working"/> <!--Fig. 2.71: --> Strain hardening of Ag/Ni 90/10 by cold working
<xr id="fig:Softening of AgNi9010 after annealing"/> <!--Fig. 2.72: --> Softening of Ag/Ni 90/10 after annealing for 1 hr after 80% cold working
<xr id="fig:Strain hardening of AgNi8020"/> <!--Fig. 2.73: --> Strain hardening of Ag/Ni 80/20 by cold working
<xr id="fig:Softening of AgNi8020 after annealing"/> <!--Fig. 2.74: --> Softening of Ag/Ni 80/20 after annealing for 1 hr after 80% cold working
<xr id="fig:Micro structure of AgNi9010"/> <!--Fig. 2.75: --> Micro structure of Ag/Ni 90/10 a) perpendicular to the extrusion direction b) parallel to the extrusion direction
<xr id="fig:Micro structure of AgNi 8020"/> <!--Fig. 2.76: --> Micro structure of Ag/Ni 80/20 a) perpendicular to the extrusion direction b) parallel t o the extrusion direction
<figtable id="tab:Contact and Switching Properties of Silver-Nickel (SINIDUR) Materials">
<caption>'''<!-- Table 2.23: -->Contact and Switching Properties of Silver-Nickel (SINIDUR) Materials'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
<figtable id="tab:Application Examples and Forms of Supply for Silver-Nickel (SINIDUR) Materials">
<caption>'''<!--Table 2.24: -->Application Examples and Forms of Supply for Silver-Nickel (SINIDUR) Materials'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
|-
|Ag/Ni 90/10-80/20
|Relays ¤ Automotive Relays - <br />Automotive Relays - Resistive load - <br />Motor load
|> 10A<br />> 10A
|rowspan="9" | '''Semi-finisched Materials:'''<br />Wires, profiles,<br />clad strips,<br />Seam-welded strips,<br />Toplay strips <br />'''Contact Parts:'''<br />Contact tips, solid<br />and composite<br />rivets, Weld buttons,<br />clad, welded,<br />brazed, and riveted<br />contact parts
==== Silver-Metal Oxide Materials Ag/CdO, Ag/SnO<sub>2</sub>, Ag/ZnO====
The family of silver-metal oxide contact materials includes the material groups: silver-cadmium oxide (DODURIT CdO), silver-tin oxide (SISTADOX), and silverzinc oxide (DODURIT ZnO). Because of their very good contact and switching properties like high resistance against welding, low contact resistance, and high arc erosion resistance, silver-metal oxides have gained an outstanding position in a broad field of applications. They mainly are used in low voltage electrical switching devices like relays, installation and distribution switches, appliances, industrial controls, motor controls, and protective devices <xr id="tab:tab2.31Application Examples of Silver–Metal Oxide Materials"/> <!--(Table 2.31)-->.
*'''Silver-cadmium oxide (DODURIT CdO) materials'''
Silver-cadmium oxide (DODURIT CdO) materials with 10-15 wt% are produced by both, internal oxidation and powder metallurgical methods <xr id="figtab:fig2.25Physical and Mechanical Properties"/> <!--(Table 2.25)-->.
<figure figtable id="figtab:fig2.25Physical and Mechanical Properties">
[[File:Physical and Mechanical Properties.jpg|right|thumb|Physical and Mechanical Properties as well as Manufacturing Processes and Forms of Supply of Extruded Silver Cadmium Oxide (DODURIT CdO) Contact Materials]]
</figurefigtable>
The manufacturing of strips and wires by internal oxidation starts with a molten alloy of silver and cadmium. During a heat treatment below it's melting point in a oxygen rich atmosphere in such a homogeneous alloy the oxygen diffuses from the surface into the bulk of the material and oxidizes the Cd to CdO in a more or less fine particle precipitation inside the Ag matrix. The CdO particles are rather fine in the surface area and are becoming larger further away towards the center of the material <xr id="fig:fig2.83Micro structure of AgCdO9010"/> <!--(Fig. 2.83)-->.
During the manufacturing of Ag/CdO contact material by internal oxidation the processes vary depending on the type of semi-finished material. For Ag/CdO wires a complete oxidation of the AgCd wire is performed, followed by wire-drawing to the required diameter <xr id="fig:fig2.77Strain hardening of internally oxidized AgCdO9010"/> <!--(Figs. 2.77) --> and <xr id="fig:fig2.78Softening of internally oxidized AgCdO9010"/> <!--(Fig. 2.78)-->. The resulting material is used for example in the production of contact rivets. For Ag/CdO strip materials two processes are commonly used: Cladding of an AgCd alloy strip with fine silver followed by complete oxidation results in a strip material with a small depletion area in the center of it's thickness and a Ag backing suitable for easy attachment by brazing (sometimes called “Conventional "Conventional Ag/CdO”CdO"). Using a technology that allows the partial oxidation of a dual-strip AgCd alloy material in a higher pressure pure oxygen atmosphere yields a composite Ag/CdO strip material that has besides a relatively fine CdO precipitation also a easily brazable AgCd alloy backing <xr id="fig:fig2.85Micro structure of AgCdO9010ZH"/> <!--(Fig. 2.85)-->. These materials (DODURIT CdO ZH) are mainly used as the basis for contact profiles and contact tips.
During powder metallurgical production the powder mixed made by different processes are typically converted by pressing, sintering and extrusion to wires and strips. The high degree of deformation during hot extrusion produces a uniform and fine dispersion of CdO particles in the Ag matrix while at the same time achieving a high density which is advantageous for good contact properties <xr id="fig:fig2.84Micro structure of AgCdO9010P"/> <!--(Fig. 2.84)-->. To obtain a backing suitable for brazing, a fine silver layer is applied by either com-pound extrusion or hot cladding prior to or right after the extrusion <xr id="fig:fig2.86Micro structure of AgCdO8812WP"/> <!--(Fig. 2.86)-->.
For larger contact tips, and especially those with a rounded shape, the single tip Press-Sinter-Repress process (PSR) offers economical advantages. Thepowder mix is pressed in a die close to the final desired shape, the “green” "green" tips are sintered, and in most cases the repress process forms the final exact shape while at the same time increasing the contact density and hardness.
Using different silver powders and minor additives for the basic Ag and CdO starting materials can help influence certain contact properties for specialized applications.
<xr id="fig:fig2.77Strain hardening of internally oxidized AgCdO9010"/> <!--Fig. 2.77: --> Strain hardening of internally oxidized Ag/CdO 90/10 by cold working
<xr id="fig:fig2.78Softening of internally oxidized AgCdO9010"/> <!--Fig. 2.78: --> Softening of internally oxidized Ag/CdO 90/10 after annealing for 1 hr after 40% cold working
<xr id="fig:fig2.79Strain hardening of AgCdO9010P"/> <!--Fig. 2.79: --> Strain hardening of Ag/CdO 90/10 P by cold working
<xr id="fig:fig2.80Softening of AgCdO9010P after annealing"/> <!--Fig. 2.80: --> Softening of Ag/CdO 90/10 P after annealing for 1 hr after 40% cold working
<xr id="fig:fig2.81Strain hardening of AgCdO8812"/> <!--Fig. 2.81: --> Strain hardening of Ag/CdO 88/12 WP
<xr id="fig:fig2.82Softening of AgCdO8812WP after annealing"/> <!--Fig. 2.82: --> Softening of Ag/CdO 88/12WP after annealing for 1 hr after different degrees of cold working
<xr id="fig:fig2.83Micro structure of AgCdO9010"/> <!--Fig. 2.83: --> Micro structure of Ag/CdO 90/10 i.o. a) close to surface b) in center area
<xr id="fig:fig2.84Micro structure of AgCdO9010P"/> <!--Fig. 2.84: --> Micro structure of Ag/CdO 90/10 P: a) perpendicular to extrusion direction b) parallel to extrusion direction
<xr id="fig:fig2.85Micro structure of AgCdO9010ZH"/> <!--Fig. 2.85: --> Micro structure of Ag/CdO 90/10 ZH: 1) Ag/CdO layer 2) AgCd backing layer
<xr id="fig:fig2.86Micro structure of AgCdO8812WP"/> <!--Fig. 2.86: --> Micro structure of AgCdO 88/12 WP: a) perpendicular to extrusion direction b) parallel to extrusion direction
<div class="multiple-images">
<figure id="fig:fig2.77Strain hardening of internally oxidized AgCdO9010">
[[File:Strain hardening of internally oxidized AgCdO9010.jpg|left|thumb|<caption>Strain hardening of internally oxidized Ag/CdO 90/10 by cold working</caption>]]
</figure>
<figure id="fig:fig2.78Softening of internally oxidized AgCdO9010">
[[File:Softening of internally oxidized AgCdO9010.jpg|left|thumb|<caption>Softening of internally oxidized Ag/CdO 90/10 after annealing for 1 hr after 40% cold working</caption>]]
</figure>
<figure id="fig:fig2.79Strain hardening of AgCdO9010P">
[[File:Strain hardening of AgCdO9010P.jpg|left|thumb|<caption>Strain hardening of Ag/CdO 90/10 P by cold working</caption>]]
</figure>
<figure id="fig:fig2.80Softening of AgCdO9010P after annealing">
[[File:Softening of AgCdO9010P after annealing.jpg|left|thumb|<caption>Softening of Ag/CdO 90/10 P after annealing for 1 hr after 40% cold working</caption>]]
</figure>
<figure id="fig:fig2.81Strain hardening of AgCdO8812">
[[File:Strain hardening of AgCdO8812.jpg|left|thumb|<caption>Strain hardening of Ag/CdO 88/12 WP</caption>]]
</figure>
<figure id="fig:fig2.82Softening of AgCdO8812WP after annealing">
[[File:Softening of AgCdO8812WP after annealing.jpg|left|thumb|<caption>Softening of Ag/CdO 88/12WP after annealing for 1 hr after different degrees of cold working</caption>]]
</figure>
<figure id="fig:fig2.83Micro structure of AgCdO9010">
[[File:Micro structure of AgCdO9010.jpg|left|thumb|<caption>Micro structure of Ag/CdO 90/10 i.o. a) close to surface b) in center area</caption>]]
</figure>
<figure id="fig:fig2.84Micro structure of AgCdO9010P">
[[File:Micro structure of AgCdO9010P.jpg|left|thumb|<caption>Micro structure of Ag/CdO 90/10 P: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.85Micro structure of AgCdO9010ZH">
[[File:Micro structure of AgCdO9010ZH.jpg|left|thumb|<caption>Micro structure of Ag/CdO 90/10 ZH: 1) Ag/CdO layer 2) AgCd backing layer</caption>]]
</figure>
<figure id="fig:fig2.86Micro structure of AgCdO8812WP">
[[File:Micro structure of AgCdO8812WP.jpg|left|thumb|<caption>Micro structure of AgCdO 88/12 WP: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
*'''Silver–tin oxide (SISTADOX) materials'''
Over the past years, many Ag/CdO contact materials have been replaced by Ag/SnO<sub>2</sub> based materials with 2-14 wt% SnO<sub>2</sub> because of the toxicity of Cadmium. This changeover was further favored by the fact that Ag/SnO<sub>2</sub> contacts quite often show improved contact and switching properties such as lower arc erosion, higher weld resistance, and a significant lower tendency towards material transfer in DC switching circuits <xr id="tab:Contact and Switching Properties of Silver–Metal Oxide Materials"/><!--(Table 2.30)-->. Ag/SnO<sub>2</sub> materials have been optimized for a broad range of applications by other metal oxide additives and modification in the manufacturing processes that result in different metallurgical, physical and electrical properties<xr id="tab:tab2.28"/><!--(Tab. 2.28)--> und <xr id="tab:tab2.29"/><!--(Table 2.29)-->.
*'''Silver–tin oxide(SISTADOX)materials'''Over the past years, many Ag/CdO contact materials have been replaced by Manufacturing of Ag/SnO<sub>2</sub> based materials with 2-14 by ''internal oxidation'' is possible in principle, but during heat treatment of alloys containing > 5 wt% SnO<sub>2</sub> because of tin in oxygen, dense oxide layers formed on the surface of the material prohibit the further diffusion of oxygen into the toxicity bulk of Cadmiumthe material. This changeover was further favored by By adding Indium or Bismuth to the alloy the fact internal oxidation is possible and results in materials that Ag/SnO<sub>2</sub> contacts quite often typically are rather hard and brittle and may show improved somewhat elevated contact and switching properties such as lower arc erosion, higher weld resistance, and is limited to applications in relays. To make a significant lower tendency towards ductile material transfer in DC switching circuits with fine oxide dispersion (SISTADOX TOS F) <xr id="tabfig:tab2.30Micro structure of Ag SnO2 88 12 TOS F"/> <!--(Table Fig. 2.30114). Ag/SnO<sub>2</sub--> it is necessary to use special process variations in oxidation and extrusion which lead to materials have been optimized for with improved properties in relays. Adding a broad range of applications by other metal oxide additives and modification brazable fine silver layer to such materials results in a semifinished material suitable for the manufacturing processes that result in different metallurgical, physical and electrical propertiesmanufacture as smaller weld profiles (SISTADOX WTOS F) <xr id="tabfig:tab2.28Micro structure of Ag SnO2 92 8 WTOS F"/> <!--(TabFig. 2.28116) und -->. Because of their resistance to material transfer and low arc erosion these materials find for example a broader application in automotive relays <xr id="tab:tab2.29Application Examples of Silver–Metal Oxide Materials"/> <!--(Table 2.2931)-->.
Manufacturing of Ag/SnO<sub>2</sub> by ''internal oxidation'' is possible in principle, but during heat treatment of alloys containing > 5 wt% of tin in oxygen, dense oxide layers formed on the surface of the material prohibit the further diffusion of oxygen into the bulk of the material. By adding Indium or Bismuth to the alloy the internal oxidation is possible and results in materials that typically are rather hard and brittle and may show somewhat elevated contact resistance and is limited to applications in relays. To make a ductile material with fine oxide dispersion (SISTADOX TOS F) <xr id="fig:fig2.114"/> (Fig. 2.114) it is necessary to use special process variations in oxidation and extrusion which lead to materials with improved properties in relays. Adding a brazable fine silver layer to such materials results in a semifinished material suitable for the manufacture as smaller weld profiles
(SISTADOX WTOS F) <xr id="fig:fig2.116"/> (Fig. 2.116). Because of their resistance to material transfer and low arc erosion these materials find for example a broader
application in automotive relays <xr id="tab:tab2.31"/> (Table 2.31).
''Powder metallurgy'' plays a significant role in the manufacturing of Ag/SnO<sub>2</sub> contact materials. Besides SnO<sub>2</sub> a smaller amount (<1 wt%) of one or more other metal oxides such as WO<sub>3</sub>, MoO<sub>3</sub>, CuO and/or Bi<sub>2</sub>O<sub>3</sub> are added. These
additives improve the wettability of the oxide particles and increase the viscosity of the Ag melt. They also provide additional benefits to the mechanical and arcing contact properties of materials in this group <xr id="figtab:fig2.26Physical Mechanical Properties as Manufacturing"/> (Table 2.26 als PDF herunterladen: [[File:Physical Mechanical properties.pdf|Physical and Mechanical Properties as well as Manufacturing Processes and
Forms of Supply of Extruded Silver-Tin Oxide (SISTADOX) Contact Materials]] )''.
'''Table 2.26: Physical and Mechanical Properties as well as Manufacturing Processes and Forms of Supply of Extruded Silver-Tin Oxide (SISTADOX) Contact Materials'''
<figure figtable id="figtab:fig2.26Physical Mechanical Properties as Manufacturing">
[[File:Physical Mechanical Properties as Manufacturing.jpg|right|thumb|Physical and Mechanical Properties as well as Manufacturing Processes and
Forms of Supply of Extruded Silver-Tin Oxide (SISTADOX) Contact Materials]]
</figurefigtable>
In the manufacture the initial powder mixes different processes are applied which provide specific advantages of the resulting materials in respect to their contact properties <!--[[#figures|(Figs. 43 – 75)]]-->. Some of them are described here as follows:
:'''a) Powder blending from single component powders''' <br> In this common process all components including additives that are part of the powder mix are blended as single powders. The blending is usually performed in the dry stage in blenders of different design.
:'''b) Powder blending on the basis of doped powders''' <br> For incorporation of additive oxides in the SnO<sub>2</sub> powder the reactive spray process (RSV) has shown advantages. This process starts with a waterbased solution of the tin and other metal compounds. This solution is nebulized under high pressure and temperature in a reactor chamber. Through the rapid evaporation of the water each small droplet is converted into a salt crystal and from there by oxidation into a tin oxide particle in which the additive metals are distributed evenly as oxides. The so created doped AgSnO2 AgSnO<sub>2</sub> powder is then mechanically mixed with silver powder.
:'''c) Powder blending based on coated oxide powders''' <br> In this process tin oxide powder is blended with lower meting additive oxides such as for example Ag<sub>2</sub> MoO<sub>4</sub> and then heat treated. The SnO<sub>2</sub> particles are coated in this step with a thin layer of the additive oxide.
:'''e) Powder blending based on chemically precipitated compound powders''' <br> A silver salt solution is added to a suspension of for example SnO<sub>2</sub> together with a precipitation agent. In a chemical reaction silver and silver oxide respectively are precipitated around the additive metal oxide particles who act as crystallization sites. Further chemical treatment then reduces the silver oxide with the resulting precipitated powder being a mix of Ag and SnO<sub>2</sub>.
Further processing of these differently produced powders follows the conventional processes of pressing, sintering and hot extrusion to wires and strips. From these contact parts such as contact rivets and tips are manufactured. To obtain a brazable backing the same processes as used for Ag/CdO are applied. As for Ag/CdO, larger contact tips can also be manufactured more economically using the press-sinter-repress (PSR) process <xr id="tab:tab2.27Physical Properties of Powder Metallurgical Silver-Metal Oxide Materials with Fine Silver Backing Produced by the Press-Sinter-Repress Process"/> <!--(Table 2.27)-->.
<div id="figures">
<xr id="fig:fig2.87Strain hardening of AgSNO2 92 8 PE"/> <!--Fig. 2.87: --> Strain hardening of Ag/SnO<sub>2</sub> 92/8 PE by cold working
<xr id="fig:fig2.88Softening of AgSnO2 92 8 PE"/> <!--Fig. 2.88: --> Softening of Ag/SnO<sub>2</sub> 92/8 PE after annealing for 1 hr after 40% cold working
<xr id="fig:fig2.89Strain hardening of Ag SnO2 88 12 PE"/> <!--Fig. 2.89: --> Strain hardening of Ag/SnO<sub>2</sub> 88/12 PE by cold working
<xr id="fig:fig2.90Softening of Ag SnO2 88 12 PE after annealing"/> <!--Fig. 2.90: --> Softening of Ag/SnO<sub>2</sub> 88/12 PE after annealing for 1 hr after 40% cold working
<xr id="fig:fig2.91Strain hardening of oxidized AgSnO2 88 12 PW4"/> <!--Fig. 2.91: --> Strain hardening of oxidized Ag/SnO<sub>2</sub> 88/12 PW4 by cold working
<xr id="fig:fig2.92Softening of Ag SnO2 88 12 PW4 after annealing"/> <!--Fig. 2.92: --> Softening of Ag/SnO<sub>2</sub> 88/12 PW4 after annealing for 1 hr after 30% cold working
<xr id="fig:fig2.93Strain hardening of Ag SnO2 98 2 PX"/> <!--Fig. 2.93: --> Strain hardening of Ag/SnO<sub>2</sub> 98/2 PX by cold working
<xr id="fig:fig2.94Softening of Ag SnO2 98 2 PX after annealing"/> <!--Fig. 2.94: --> Softening of Ag/SnO<sub>2</sub> 98/2 PX after annealing for 1 hr after 80% cold working
<xr id="fig:fig2.95Strain hardening of Ag SnO2 92 8 PX"/> <!--Fig 2.95: --> Strain hardening of Ag/SnO<sub>2</sub> 92/8 PX by cold working
<xr id="fig:fig2.96Softening of Ag SnO2 92 8 PX after annealing"/> <!--Fig. 2.96: --> Softening of Ag/SnO<sub>2</sub> 92/8 PX after annealing for 1 hr after 40% cold working
<xr id="fig:fig2.97Strain hardening of internally oxidized Ag SnO2 88 12 TOS F"/> <!--Fig. 2.97: --> Strain hardening of internally oxidized Ag/SnO<sub>2</sub> 88/12 TOS F by cold working
<xr id="fig:fig2.98Softening of Ag SnO2 88 12 TOS F after annealing"/> <!--Fig. 2.98: --> Softening of Ag/SnO<sub>2</sub> 88/12 TOS F after annealing for 1 hr after 30% cold working
<xr id="fig:fig2.99Strain hardening of internally oxidized Ag SnO2 88 12P"/> <!--Fig. 2.99: --> Strain hardening of internally oxidized Ag/SnO<sub>2</sub> 88/12P by cold working
<xr id="fig:fig2.100Softening of Ag SnO2 88 12P after annealing"/> <!--Fig. 2.100: --> Softening of Ag/SnO<sub>2</sub> 88/12P after annealing for 1 hr after 40% cold working
<xr id="fig:fig2.101Strain hardening of Ag SnO2 88 12 WPC"/> <!--Fig. 2.101: --> Strain hardening of Ag/SnO<sub>2</sub> 88/12 WPC by cold working
<xr id="fig:fig2.102Softening of Ag SnO2 88 12 WPC after annealing"/> <!--Fig. 2.102: --> Softening of Ag/SnO<sub>2</sub> 88/12 WPC after annealing for 1 hr after different degrees of cold working
<xr id="fig:fig2.103Strain hardening of Ag SnO2 86 14 WPC"/> <!--Fig. 2.103: --> Strain hardening of Ag/SnO<sub>2</sub> 86/14 WPC by cold working
<xr id="fig:fig2.104Softening of Ag SnO2 86 14 WPC"/> <!--Fig. 2.104: --> Softening of Ag/SnO<sub>2</sub> 86/14 WPC after annealing for 1 hr after different degrees of cold working
<xr id="fig:fig2.105Strain hardening of Ag SnO2 88 12 WPD"/> <!--Fig. 2.105: --> Strain hardening of Ag/SnO<sub>2</sub> 88/12 WPD by cold working
<xr id="fig:fig2.106Softening of Ag SnO2 88 12 WPD after annealing"/> <!--Fig. 2.106: --> Softening of Ag/SnO<sub>2</sub> 88/12 WPD after annealing for 1 hr after different degrees of cold working
<xr id="fig:fig2.108Softening of Ag SnO2 88 12 WPX"/> <!--Fig. 2.108: --> Softening of Ag/SnO<sub>2</sub> 88/12 WPX after annealing for 1 hr after different degrees of cold working
<xr id="fig:fig2.107Strain hardening of Ag SnO2 88 12 WPX"/> <!--Fig. 2.107: --> Strain hardening of Ag/SnO<sub>2</sub> 88/12 WPX by cold working
<xr id="fig:fig2.109Micro structure of Ag SnO2 92 8 PE"/> <!--Fig. 2.109: --> Micro structure of Ag/SnO<sub>2</sub> 92/8 PE: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.110Micro structure of Ag SnO2 88 12 PE"/> <!--Fig. 2.110: --> Micro structure of Ag/SnO<sub>2</sub> 88/12 PE: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.111Micro structure of Ag SnO2 88 12 PW"/> <!--Fig. 2.111: --> Micro structure of Ag/SnO<sub>2</sub> 88/12 PW: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.112Micro structure of Ag SnO2 98 2 PX"/> <!--Fig. 2.112: --> Micro structure of Ag/SnO<sub>2</sub> 98/2 PX: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.113Micro structure of Ag SnO2 92 8PX"/> <!--Fig. 2.113: --> Micro structure of Ag/SnO<sub>2</sub> 92/8 PX: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.114Micro structure of Ag SnO2 88 12 TOS F"/> <!--Fig. 2.114: --> Micro structure of Ag/SnO<sub>2</sub> 88/12 TOS F: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.115Micro structure of Ag SnO2 86 14 WPC"/> <!--Fig. 2.115: --> Micro structure of Ag/SnO<sub>2</sub> 86/14 WPC: a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) AgSnO<sub>2</sub> contact layer, 2) Ag backing layer
<xr id="fig:fig2.116Micro structure of Ag SnO2 92 8 WTOS F"/> <!--Fig. 2.116: --> Micro structure of Ag/SnO<sub>2</sub> 92/8 WTOS F: a) perpendicular to extrusion direction
b) parallel to extrusion direction,1) AgSnO<sub>2</sub> contact layer, 2) Ag backing layer
<xr id="fig:fig2.117Micro structure of Ag SnO2 88 12 WPD"/> <!--Fig. 2.117: --> Micro structure of Ag/SnO<sub>2</sub> 88/12 WPD: parallel to extrusion direction
1) AgSnO<sub>2</sub> contact layer, 2) Ag backing layer
<xr id="fig:fig2.118Micro structure of Ag SnO2 88 12 WPX"/> <!--Fig. 2.118: --> Micro structure of Ag/SnO<sub>2</sub> 88/12 WPX:parallel to extrusion direction
1) AgSnO<sub>2</sub> contact layer, 2) Ag backing layer
<xr id="fig:fig2.119Micro structure of Ag SnO2 86 14 WPX"/> <!--Fig. 2.119: --> Micro structure of Ag/SnO<sub>2</sub> 86/14 WPX: a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) AgSnO<sub>2</sub> contact layer, 2) Ag backing layer
</div>
<div class="multiple-images">
<figure id="fig:fig2.87Strain hardening of AgSNO2 92 8 PE">
[[File:Strain hardening of AgSNO2 92 8 PE.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 92/8 PE by cold working</caption>]]
</figure>
<figure id="fig:fig2.88Softening of AgSnO2 92 8 PE">
[[File:Softening of AgSnO2 92 8 PE.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 92/8 PE after annealing for 1 hr after 40% cold working</caption>]]
</figure>
<figure id="fig:fig2.89Strain hardening of Ag SnO2 88 12 PE">
[[File:Strain hardening of Ag SnO2 88 12 PE.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 88/12 PE by cold working</caption>]]
</figure>
<figure id="fig:fig2.90Softening of Ag SnO2 88 12 PE after annealing">
[[File:Softening of Ag SnO2 88 12 PE after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 88/12 PE after annealing for 1 hr after 40% cold working</caption>]]
</figure>
<figure id="fig:fig2.91Strain hardening of oxidized AgSnO2 88 12 PW4">
[[File:Strain hardening of oxidized AgSnO2 88 12 PW4.jpg|left|thumb|<caption>Strain hardening of oxidized Ag/SnO<sub>2</sub> 88/12 PW4 by cold working</caption>]]
</figure>
<figure id="fig:fig2.92Softening of Ag SnO2 88 12 PW4 after annealing">
[[File:Softening of Ag SnO2 88 12 PW4 after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 88/12 PW4 after annealing for 1 hr after 30% cold working</caption>]]
</figure>
<figure id="fig:fig2.93Strain hardening of Ag SnO2 98 2 PX">
[[File:Strain hardening of Ag SnO2 98 2 PX.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 98/2 PX by cold working</caption>]]
</figure>
<figure id="fig:fig2.94Softening of Ag SnO2 98 2 PX after annealing">
[[File:Softening of Ag SnO2 98 2 PX after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 98/2 PX after annealing for 1 hr after 80% cold working</caption>]]
</figure>
<figure id="fig:fig2.95Strain hardening of Ag SnO2 92 8 PX">
[[File:Strain hardening of Ag SnO2 92 8 PX.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 92/8 PX by cold working</caption>]]
</figure>
<figure id="fig:fig2.96Softening of Ag SnO2 92 8 PX after annealing">
[[File:Softening of Ag SnO2 92 8 PX after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 92/8 PX after annealing for 1 hr after 40% cold working</caption>]]
</figure>
<figure id="fig:fig2.97Strain hardening of internally oxidized Ag SnO2 88 12 TOS F">
[[File:Strain hardening of internally oxidized Ag SnO2 88 12 TOS F.jpg|left|thumb|<caption>Strain hardening of internally oxidized Ag/SnO<sub>2</sub> 88/12 TOS F by cold working</caption>]]
</figure>
<figure id="fig:fig2.98Softening of Ag SnO2 88 12 TOS F after annealing">
[[File:Softening of Ag SnO2 88 12 TOS F after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 88/12 TOS F after annealing for 1 hr after 30% cold working</caption>]]
</figure>
<figure id="fig:fig2.99Strain hardening of internally oxidized Ag SnO2 88 12P">
[[File:Strain hardening of internally oxidized Ag SnO2 88 12P.jpg|left|thumb|<caption>Strain hardening of internally oxidized Ag/SnO<sub>2</sub> 88/12P by cold working</caption>]]
</figure>
<figure id="fig:fig2.100Softening of Ag SnO2 88 12P after annealing">
[[File:Softening of Ag SnO2 88 12P after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub>88/12P after annealing for 1 hr after 40% cold working</caption>]]
</figure>
<figure id="fig:fig2.101Strain hardening of Ag SnO2 88 12 WPC">
[[File:Strain hardening of Ag SnO2 88 12 WPC.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 88/12 WPC by cold working</caption>]]
</figure>
<figure id="fig:fig2.102Softening of Ag SnO2 88 12 WPC after annealing">
[[File:Softening of Ag SnO2 88 12 WPC after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 88/12 WPC after annealing for 1 hr after different degrees of cold working</caption>]]
</figure>
<figure id="fig:fig2.103Strain hardening of Ag SnO2 86 14 WPC">
[[File:Strain hardening of Ag SnO2 86 14 WPC.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 86/14 WPC by cold working</caption>]]
</figure>
<figure id="fig:fig2.104Softening of Ag SnO2 86 14 WPC">
[[File:Softening of Ag SnO2 86 14 WPC.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 86/14 WPC after annealing for 1 hr after different degrees of cold working</caption>]]
</figure>
<figure id="fig:fig2.105Strain hardening of Ag SnO2 88 12 WPD">
[[File:Strain hardening of Ag SnO2 88 12 WPD.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 88/12 WPD by cold working</caption>]]
</figure>
<figure id="fig:fig2.106Softening of Ag SnO2 88 12 WPD after annealing">
[[File:Softening of Ag SnO2 88 12 WPD after annealing.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 88/12 WPD after annealing for 1 hr after different degrees of cold working</caption>]]
</figure>
<figure id="fig:fig2.108Softening of Ag SnO2 88 12 WPX">
[[File:Softening of Ag SnO2 88 12 WPX.jpg|left|thumb|<caption>Softening of Ag/SnO<sub>2</sub> 88/12 WPX after annealing for 1 hr after different degrees of cold working</caption>]]
</figure>
<figure id="fig:fig2.107Strain hardening of Ag SnO2 88 12 WPX">
[[File:Strain hardening of Ag SnO2 88 12 WPX.jpg|left|thumb|<caption>Strain hardening of Ag/SnO<sub>2</sub> 88/12 WPX by cold working</caption>]]
</figure>
<figure id="fig:fig2.109Micro structure of Ag SnO2 92 8 PE">
[[File:Micro structure of Ag SnO2 92 8 PE.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 92/8 PE: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.110Micro structure of Ag SnO2 88 12 PE">
[[File:Micro structure of Ag SnO2 88 12 PE.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 88/12 PE: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.111Micro structure of Ag SnO2 88 12 PW">
[[File:Micro structure of Ag SnO2 88 12 PW.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 88/12 PW: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.112Micro structure of Ag SnO2 98 2 PX">
[[File:Micro structure of Ag SnO2 98 2 PX.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 98/2 PX: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.113Micro structure of Ag SnO2 92 8PX">
[[File:Micro structure of Ag SnO2 92 8PX.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 92/8 PX: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.114Micro structure of Ag SnO2 88 12 TOS F">
[[File:Micro structure of Ag SnO2 88 12 TOS F.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 88/12 TOS F: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.115Micro structure of Ag SnO2 86 14 WPC">
[[File:Micro structure of Ag SnO2 86 14 WPC.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 86/14 WPC: a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) AgSnO2 contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.116Micro structure of Ag SnO2 92 8 WTOS F">
[[File:Micro structure of Ag SnO2 92 8 WTOS F.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 92/8 WTOS F: a) perpendicular to extrusion direction b) parallel to extrusion direction,1) AgSnO2 contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.117Micro structure of Ag SnO2 88 12 WPD">
[[File:Micro structure of Ag SnO2 88 12 WPD.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 88/12 WPD: parallel to extrusion direction 1) AgSnO2 contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.118Micro structure of Ag SnO2 88 12 WPX">
[[File:Micro structure of Ag SnO2 88 12 WPX.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 88/12 WPX:parallel to extrusion direction 1) AgSnO2 contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.119Micro structure of Ag SnO2 86 14 WPX">
[[File:Micro structure of Ag SnO2 86 14 WPX.jpg|left|thumb|<caption>Micro structure of Ag/SnO<sub>2</sub> 86/14 WPX: a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) AgSnO2 contact layer, 2) Ag backing layer</caption>]]
</figure>
<figtable id="tab:tab2.27Physical Properties of Powder Metallurgical Silver-Metal Oxide Materials with Fine Silver Backing Produced by the Press-Sinter-Repress Process"><caption>'''<!--Table 2.27: -->Physical Properties of Powder Metallurgical Silver-Metal Oxide Materials with Fine Silver Backing Produced by the Press-Sinter-Repress Process'''</caption>
<table class="twocolortable">
<tr><th rowspan="2"><p class="s11">Material/</p><p class="s11">DODUCO- Designation</p></th><th rowspan="2"><p class="s11">Additives</p></th><th rowspan="2"><p class="s11">Density</p><p class="s11">[ g/cm<sup>3</sup>]</p></th><th rowspan="2"><p class="s11">Electrical</p><p class="s11">Resistivity</p><p class="s11">[µ<span class="s14">S ·</span>cm]</p></th><th colspan="2"><p class="s11">Electrical</p><p class="s11">Conductivity</p></th><th rowspan="2"><p class="s11">Vickers</p><p class="s11">Hardness</p><p class="s11">HV 10.</p></th></tr>
*'''Silver–zinc oxide (DODURIT ZnO) materials'''
Silver zinc oxide (DODURIT ZnO) contact materials with mostly 6 - 10 wt% oxide content including other small metal oxides are produced exclusively by powder metallurgy [[#figures1|(Figs. 76 – 81)]], <!--(Table 2.28)-->. Adding Ag<sub>2</sub>WO<sub>4</sub> in the process b) as described in the preceding chapter on Ag/SnO<sub>2</sub> has proven most effective for applications in AC relays, wiring devices, and appliance controls. Just like with the other Ag metal oxide materials, semi-finished materials in strip and wire form are used to manufacture contact tips and rivets. Because of their high resistance against welding and arc erosion Ag/ZnO materials present an economic alternative to Cd free Ag-tin oxide contact materials <xr id="tab:tab2.30Contact and Switching Properties of Silver–Metal Oxide Materials"/> <!--(Tab. 2.30) --> and <xr id="tab:tab2.31Application Examples of Silver–Metal Oxide Materials"/> <!--(Tab. 2.31)-->.
<figtable id="tab:tab2.28">
<caption>'''<!--Table 2.28: --> Physical and Mechanical Properties as well as Manufacturing Processes and Forms of Supply of Extruded Silver-Zinc Oxide (DODURIT ZnO) Contact'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
<div id="figures1">
<xr id="fig:fig2.120Strain hardening of Ag ZnO 92 8 PW25"/> <!--Fig. 2.120: --> Strain hardening of Ag/ZnO 92/8 PW25 by cold working
<xr id="fig:fig2.121Softening of Ag ZnO 92 8 PW25"/> <!--Fig. 2.121: --> Softening of Ag/ZnO 92/8 PW25 after annealing for 1 hr after 30% cold working
<xr id="fig:fig2.122Strain hardening of Ag ZnO 92 8 WPW25"/> <!--Fig. 2.122: --> Strain hardening of Ag/ZnO 92/8 WPW25 by cold working
<xr id="fig:fig2.123Softening of Ag ZnO 92 8 WPW25"/> <!--Fig. 2.123: --> Softening of Ag/ZnO 92/8 WPW25 after annealing for 1hr after different degrees of cold working
<xr id="fig:fig2.124Micro structure of Ag ZnO 92 8 Pw25"/> <!--Fig. 2.124: --> Micro structure of Ag/ZnO 92/8 Pw25: a) perpendicular to extrusion direction
b) parallel to extrusion direction
<xr id="fig:fig2.125Micro structure of Ag ZnO 92 8 WPW25"/> <!--Fig. 2.125: --> Micro structure of Ag/ZnO 92/8 WPW25:a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) Ag/ZnO contact layer, 2) Ag backing layer
</div>
<div class="multiple-images">
<figure id="fig:fig2.120Strain hardening of Ag ZnO 92 8 PW25">
[[File:Strain hardening of Ag ZnO 92 8 PW25.jpg|left|thumb|<caption>Strain hardening of Ag/ZnO 92/8 PW25 by cold working</caption>]]
</figure>
<figure id="fig:fig2.121Softening of Ag ZnO 92 8 PW25">
[[File:Softening of Ag ZnO 92 8 PW25.jpg|left|thumb|<caption>Softening of Ag/ZnO 92/8 PW25 after annealing for 1 hr after 30% cold working</caption>]]
</figure>
<figure id="fig:fig2.122Strain hardening of Ag ZnO 92 8 WPW25">
[[File:Strain hardening of Ag ZnO 92 8 WPW25.jpg|left|thumb|<caption>Strain hardening of Ag/ZnO 92/8 WPW25 by cold working</caption>]]
</figure>
<figure id="fig:fig2.123Softening of Ag ZnO 92 8 WPW25">
[[File:Softening of Ag ZnO 92 8 WPW25.jpg|left|thumb|<caption>Softening of Ag/ZnO 92/8 WPW25 after annealing for 1hr after different degrees of cold working</caption>]]
</figure>
<figure id="fig:fig2.124Micro structure of Ag ZnO 92 8 Pw25">
[[File:Micro structure of Ag ZnO 92 8 Pw25.jpg|left|thumb|<caption>Micro structure of Ag/ZnO 92/8 Pw25: a) perpendicular to extrusion direction b) parallel to extrusion direction</caption>]]
</figure>
<figure id="fig:fig2.125Micro structure of Ag ZnO 92 8 WPW25">
[[File:Micro structure of Ag ZnO 92 8 WPW25.jpg|right|thumb|<caption>Micro structure of Ag/ZnO 92/8 WPW25:a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) Ag/ZnO contact layer, 2) Ag backing layer</caption>]]
</figure>
</div>
<div class="clear"></div>
 
<figtable id="tab:tab2.29">
<caption>'''<!--Table 2.29: -->Optimizing of Silver–Tin Oxide Materials Regarding their Switching Properties and Forming Behavior'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material/</p><p class="s12">Material Group</p></th><th><p class="s12">Special Properties<th colspan="2"></p></th></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>PE</p></td><td><p class="s12">Especially suitable for automotive relays</p><p class="s12">(lamp loads)</p></td><td><p class="s12">Good formability (contact rivets)</p></td></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>98/2 PX/PC</p></td><td><p class="s12">Especially good heat resistance</p></td><td><p class="s12">Easily riveted, can be directly welded</p></td></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>TOS F</p></td><td><p class="s12">Especially suited for high inductive</p><p class="s12">DC loads</p></td><td><p class="s12">Very good formability (contact rivets)</p></td></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>WPC</p></td><td><p class="s12">For AC-3 and AC-4 applications in motor</p><p class="s12">switches (contactors)</p></td><td/></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>WPD</p></td><td><p class="s12">Especially suited for severe loads (AC-4)</p><p class="s12">and high switching currents</p></td><td/></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>WPX</p></td><td><p class="s12">For standard motor loads (AC-3) and</p><p class="s12">Resistive loads (AC-1), DC loads (DC-5)</p></td><td/></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2 </span>WTOSF</p></td><td><p class="s12">Especially suitable for high inductive DC</p><p class="s12">loads</p></td><td/></tr></table>
<figtable id="tab:tab2.30Contact and Switching Properties of Silver–Metal Oxide Materials"><caption>'''<!--Table 2.30: -->Contact and Switching Properties of Silver–Metal Oxide Materials'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
</figtable>
 <figtable id="tab:tab2.31Application Examples of Silver–Metal Oxide Materials"><caption>'''<!--Table 2.31: -->Application Examples of Silver–Metal Oxide Materials'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material</p></th><th><p class="s12">Application Examples</p></th></tr><tr><td><p class="s12">Ag/CdO</p></td><td><p class="s12">Micro switches, Network relays, Wiring devices, Appliance switches, Main switches, contactors, Small (main) power switches</p></td></tr><tr><td><p class="s12">Ag/SnO<span class="s48">2</span></p></td><td><p class="s12">Micro switches, Network relays, Automotive relays, Appliance switches,</p><p class="s12">Main switches, contactors, Fault current protection relays (paired against</p><p class="s12">Ag/C), (Main) Power switches</p></td></tr><tr><td><p class="s12">Ag/ZnO</p></td><td><p class="s12">Wiring devices, AC relays, Appliance switches, Motor-protective circuit</p><p class="s12">breakers (paired with Ag/Ni or Ag/C), Fault current circuit breakers paired againct Ag/C, (Main) Power switches</p></td></tr></table>
====Silver–Graphite (GRAPHOR)-Materials====
Ag/C (GRAPHOR) contact materials are usually produced by powder metallurgy with graphite contents of 2 – 5 wt% <xr id="tab:tab2.32"/> <!--(Table 2.32)-->. The earlier typical manufacturing process of single pressed tips by pressing - sintering - repressing (PSR) has been replaced in Europe for quite some time by extrusion. In North America and some other regions however the PSR process is still used to some extend mainly for cost reasons.
The extrusion of sintered billets is now the dominant manufacturing method for semi-finished AgC materials <!--[[#figures3|(Figs. 82 – 85)]]<!--(Figs. 2.126 – 2.129)-->. The hot extrusion process results in a high density material with graphite particles stretched and oriented in the extrusion direction [[#figures4|(Figs. 86 – 89)]]<!--(Figs. 2.130 – 2.133)''-->. Depending on the extrusion method in either rod or strip form the graphite particles can be oriented in the finished contact tips perpendicular (GRAPHOR) or parallel (GRAPHOR D) to the switching contact surface <xr id="fig:fig2.131Micro structure of Ag C 95 5"/> <!--(Fig. 2.131) --> and <xr id="fig:fig2.132Micro structure of Ag C 96 4 D"/> <!--(Fig. 2.132)-->.
Since the graphite particles in the Ag matrix of Ag/C materials prevent contact tips from directly being welded or brazed, a graphite free bottom layer is required. This is achieved by either burning out (de-graphitizing) the graphite selectively on one side of the tips or by compound extrusion of a Ag/C billet covered with a fine silver shell.
Ag/C contact materials exhibit on the one hand an extremely high resistance to contact welding but on the other have a low arc erosion resistance. This is caused by the reaction of graphite with the oxygen in the surrounding atmosphere at the high temperatures created by the arcing. The weld resistanceis especially high for materials with the graphite particle orientation parallel to the arcing contact surface. Since the contact surface after arcing consists of pure silver the contact resistance stays consistently low during the electrical life of the contact parts.
A disadvantage of the Ag/C materials is their rather high erosion rate. In materials with parallel graphite orientation this can be improved if part of the graphite is incorporated into the material in the form of fibers (GRAPHOR DF), <xr id="fig:fig2.133Micro structure of Ag C DF"/> <!--(Fig. 2.133)-->. The weld resistance is determined by the total content of graphite particles.
Ag/C tips with vertical graphite particle orientation are produced in a specific sequence: Extrusion to rods, cutting of double thickness tips, burning out of graphite to a controlled layer thickness, and a second cutting to single tips. Such contact tips are especially well suited for applications which require both, a high weld resistance and a sufficiently high arc erosion resistance <xr id="tab:tab2.33"/> <!--(Table 2.33)-->. For attachment of Ag/C tips welding and brazing techniques are applied.
welding the actual process depends on the material's graphite orientation. For Ag/C tips with vertical graphite orientation the contacts are assembled with single tips. For parallel orientation a more economical attachment starting with contact material in strip or profile tape form is used in integrated stamping and welding operations with the tape fed into the weld station, cut off to tip form and then welded to the carrier material before forming the final contact assembly part. For special low energy welding the Ag/C profile tapes GRAPHOR D and DF can be pre-coated with a thin layer of high temperature brazing alloys such as CuAgP.
In a rather limited way, Ag/C with 2 – 3 wt% graphite can be produced in wire form and headed into contact rivet shape with low head deformation ratios.
The main applications for Ag/C materials are protective switching devices such as miniature molded case circuit breakers, motor-protective circuit breakers, and fault current circuit breakers, where during short circuit failures highest resistance against welding is required <xr id="tab:tab2.34"/> <!--(Table 2.34)-->. For higher currents the low arc erosion resistance of Ag/C is compensated by asymmetrical pairing with more erosion resistant materials such as Ag/Ni and Ag/W.
<div id="figures3">
<xr id="fig:fig2.126Strain hardening of Ag C 96 4 D"/> <!--Fig. 2.126: --> Strain hardening of Ag/C 96/4 D by cold working
<xr id="fig:fig2.127Softening of Ag C 96 4 D"/> <!--Fig. 2.127: --> Softening of Ag/C 96/4 D after annealing
<xr id="fig:fig2.128Strain hardening of Ag C DF"/> <!--Fig. 2.128: --> Strain hardening of Ag/C DF by cold working
<xr id="fig:fig2.129Softening of Ag C DF after annealing"/> <!--Fig. 2.129: --> Softening of Ag/C DF after annealing
</div>
<div id="figures4">
<xr id="fig:fig2.130Micro structure of Ag C 97 3"/> <!--Fig. 2.130: --> Micro structure of Ag/C 97/3: a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag backing layer
<xr id="fig:fig2.131Micro structure of Ag C 95 5"/> <!--Fig. 2.131: --> Micro structure of Ag/C 95/5: a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag backing layer
<xr id="fig:fig2.132Micro structure of Ag C 96 4 D"/> <!--Fig. 2.132: --> Micro structure of Ag/C 96/4 D: a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag backing layer
<xr id="fig:fig2.133Micro structure of Ag C DF"/> <!--Fig. 2.133: --> Micro structure of Ag/C DF: a) perpendicular to extrusion direction
b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag/Ni 90/10 backing layer
</div>
<div class="multiple-images">
<figure id="fig:fig2.126Strain hardening of Ag C 96 4 D">
[[File:Strain hardening of Ag C 96 4 D.jpg|left|thumb|<caption>Strain hardening of Ag/C 96/4 D by cold working</caption>]]
</figure>
<figure id="fig:fig2.127Softening of Ag C 96 4 D">
[[File:Softening of Ag C 96 4 D.jpg|left|thumb|<caption>Softening of Ag/C 96/4 D after annealing</caption>]]
</figure>
<figure id="fig:fig2.128Strain hardening of Ag C DF">
[[File:Strain hardening of Ag C DF.jpg|left|thumb|<caption>Strain hardening of Ag/C DF by cold working</caption>]]
</figure>
<figure id="fig:fig2.129Softening of Ag C DF after annealing">
[[File:Softening of Ag C DF after annealing.jpg|left|thumb|<caption>Softening of Ag/C DF after annealing</caption>]]
</figure>
<figure id="fig:fig2.130Micro structure of Ag C 97 3">
[[File:Micro structure of Ag C 97 3.jpg|left|thumb|<caption>Micro structure of Ag/C 97/3: a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.131Micro structure of Ag C 95 5">
[[File:Micro structure of Ag C 95 5.jpg|left|thumb|<caption>Micro structure of Ag/C 95/5: a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.132Micro structure of Ag C 96 4 D">
[[File:Micro structure of Ag C 96 4 D.jpg|left|thumb|<caption>Micro structure of Ag/C 96/4 D: a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag backing layer</caption>]]
</figure>
<figure id="fig:fig2.133Micro structure of Ag C DF">
[[File:Micro structure of Ag C DF.jpg|left|thumb|<caption>Micro structure of Ag/C DF: a) perpendicular to extrusion direction b) parallel to extrusion direction, 1) Ag/C contact layer, 2) Ag/Ni 90/10 backing layer</caption>]]
</figure>
<figtable id="tab:tab2.32">
<caption>'''<!--Table 2.32: -->Physical Properties of Silver–Graphite (GRAPHOR) Contact Materials'''</caption>
{| class="twocolortable" style="text-align: left; font-size: 12px"
<figtable id="tab:tab2.33">
<caption>'''<!--Table 2.33: -->Contact and Switching properties of Silver–Graphite (GRAPHOR) Contact Materials'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material/</p><p class="s12">DODUCO-Designation</p></th><th><p class="s11">Properties</p></th></tr><tr><td><p class="s12">Ag/C</p><p class="s12">GRAPHOR</p></td><td><p class="s12">Highest resistance against welding during make operations at high currents,</p><p class="s12">High resistance against welding of closed contacts during short circuit,</p><p class="s12">Increase of weld resistance with higher graphite contents, Low contact resistance,</p><p class="s12">Low arc erosion resistance, especially during break operations, Higher arc erosion with increasing graphite contents, at the same time carbon build-up on switching chamber walls increases, GRAPHOR with vertical orientation has better arc erosion resistance, parallel orientation has better weld resistance,</p><p class="s12">Limited arc moving properties, therefore paired with other materials,</p><p class="s12">Limited formability,</p><p class="s12">Can be welded and brazed with decarbonized backing, GRAPHOR DF is optimized for arc erosion resistance and weld resistance</p></td></tr></table>
<figtable id="tab:tab2.34">
<caption>'''<!--Table 2.34: -->Application Examples and Forms of Supply of Silver– Graphite (GRAPHOR) Contact Materials'''</caption>
<table class="twocolortable">
<tr><th><p class="s12">Material/</p><p class="s12">DODUCO Designation</p></th><th><p class="s12">Application Examples</p></th><th><p class="s12">Form of Supply</p></th></tr><tr><td><p class="s12">Ag/C 98/2</p><p class="s12">GRAPHOR 2</p></td><td><p class="s12">Motor circuit breakers, paired with Ag/Ni</p></td><td><p class="s12">Contact tips, brazed and welded contact parts, some contact rivets</p></td></tr><tr><td><p class="s12">Ag/C 97/3</p><p class="s12">GRAPHOR 3</p><p class="s12">Ag/C 96/4</p><p class="s12">GRAPHOR 4</p><p class="s12">Ag/C 95/5</p><p class="s12">GRAPHOR 5</p><p class="s12">GRAPHOR 3D GRAPHOR 4D GRAPHOR DF</p></td><td><p class="s12">Circuit breakers, paired with Cu, Motor-protective circuit breakers, paired with Ag/Ni,</p><p class="s12">Fault current circuit breakers, paired with Ag/Ni, Ag/W, Ag/WC, Ag/SnO<span class="s45">2</span>, Ag/ZnO,</p><p class="s12">(Main) Power switches, paired with Ag/Ni, Ag/W</p></td><td><p class="s12">Contact tips, brazed and welded contact</p><p class="s12">parts, some contact rivets with</p><p class="s12">Ag/C97/3</p></td></tr><tr><td><p class="s12">Ag/C 97/3</p><p class="s12">GRAPHOR 3</p><p class="s12">Ag/C 96/4</p><p class="s12">GRAPHOR 4</p><p class="s12">Ag/C 95/5</p><p class="s12">GRAPHOR 5</p><p class="s12">GRAPHOR 3D GRAPHOR 4D GRAPHOR DF</p></td><td><p class="s12">Circuit breakers, paired with Cu, Motor-protective circuit breakers, paired with Ag/Ni,</p><p class="s12">Fault current circuit breakers, paired with Ag/Ni, Ag/W, Ag/WC, Ag/SnO<span class="s45">2</span>, Ag/ZnO,</p><p class="s12">(Main) Power switches, paired with Ag/Ni, Ag/W</p></td><td><p class="s12">Contact profiles (weld tapes), Contact tips, brazed and welded contact parts</p></td></tr><tr><td/><td/></tr></table>
==References==
[[Contact Materials for Electrical Engineering#References|References]]
 
[[de:Werkstoffe_auf_Silber-Basis]]

Navigation menu

Powered by