210
edits
Changes
temp edit
beschrieben werden.
<figure id="fig:Hot_cladding_of_pre_materials">
[[File:Hot cladding of pre-materials (schematisch).jpg|right|thumb|Hot cladding of pre-materials Warmpressschweißen von Kontaktbimetall (schematisch)]]
</figure>
<figure id="fig:Cold roll-cladding of semi-finished strips (schematic)">
[[File:Cold roll-cladding of semi-finished strips (schematic).jpg|right|thumb|Cold roll-cladding of semi-finished strips Kaltwalzplattieren von Kontaktbimetall (schematicschematisch)]]
</figure>
*Typical configurations of clad contact strips Typische Ausführungsformen für Kontaktbimetalle <xr id="fig:Typical configurations of clad contact strips"/>
<figure id="fig:Typical configurations of clad contact strips">
[[File:Typical configurations of clad contact strips.jpg|right|thumb|Typical configurations of clad contact stripsTypische Ausführungsformen für Kontaktbimetalle]]
</figure>
*Contact materials Kontaktwerkstoffe <br />Ag, Ag-alloys., Ag/Ni (SINIDUR), in special cases also Sonderfällen auch Ag/CdO (DODURIT CdO), Ag/SnO<sub>2</sub> (SISTADOX), Ag/ZnO (DODURIT ZnO)<br />
*Carrier materialsTrägerwerkstoffe<br />Cu, CuSn, CuNiZn, CuNiSn, CuFe, CuBe u.a.
*Dimensions Abmessungen <xr id="fig:Dimensions"/>
<figure id="fig:Dimensions">
[[File:Dimensions.jpg|right|thumb|DimensionsAbmessungen]]
</figure>
*Quality criteria and tolerancesQualitätsmerkmale und ToleranzenStrength properties and dimensional tolerances of clad contact biFestigkeitswerte und Maßtoleranzen von Kontaktbimetallen sind an die für Cuund Cu-metals are derived from the standards DIN Legierungen geltenden Normen EN 1652 and DIN und EN 1654 for Cu alloysangelehnt. Beider Vermaßung der Breite der Edelmetalleinlage wird empfohlen, von den für diejeweilige Anwendung erforderlichen Minimalwerten auszugehen. When specifying the width of the contact material layer it is recommended to use the minimum required valueDie Vermaßungsollte stets von der Bandkante aus erfolgen. All dimensions should be specified originating from one strip edge.
=== Brazed SemiGelötete Halbzeuge (Toplay-Finished Contact Materials (Toplay–ProfilesProfile)===The toplay process starts with a flat or profile – shaped contact material strip which is fed together with the wider nonDas Toplay-Verfahren geht von einem flachen oder profilierten edelmetallhaltigenKontaktband aus, das zusammen mit einem Hartlotstreifen und demunedlen Trägerband einem Induktions-precious carrier material and in most cases an intermediate thin foil of brazing alloy into a induction brazing machine Lötautomaten zugeführt wird <xr id="fig:Toplay brazing with an inductive heating inline equipment (schematic)"/><!--(Fig. 3.5)-->. An evenly distributed and reliable braze joint can be achieved this way between contact and carrier materialsDabei lässt sich eine gleichmäßige und zuverlässige Lötverbindung zwischenKontaktauflage und Trägermaterial herstellen. The combined material strip is rather soft after the brazing process and re-hardened during a subsequent profile rolling stepDer so erzeugte Werkstoffverbundmit erhabener Edelmetallauflage ist nach dem Löten weich und wirdanschließend auf profilierten Walzen nachverfestigt. In this way different shapes and configurations can easily be achievedAuf diese Weise könnenunterschiedliche Profilformen hergestellt werden.
<figure id="fig:Toplay brazing with an inductive heating inline equipment (schematic)">
[[File:Toplay brazing with an inductive heating inline equipment (schematic).jpg|right|thumb|Toplay brazing with an inductive heating inline equipment -Lötung mit Induktionsdurchlaufanlage (schematicschematisch)]]
</figure>
*Typical configurations of toplay contact profiles Typische Ausführungsformen für Toplay-Profile <xr id="fig:Typical configurations of toplay contact profiles2"/>
<figure id="fig:Typical configurations of toplay contact profiles2">
[[File:Typical configurations of toplay contact profiles2.jpg|right|thumb|Typical configurations of toplay contact profilesTypische Ausführungsformen für Toplay-Profile]]
</figure>
*Contact materials Kontaktwerkstoffe <br />Ag, AgNi 0,15 (ARGODUR), AgCu, AgCuNi (ARGODUR 27), Ag/Ni (SINIDUR),
Ag/CdO (DODURIT CdO), Ag/SnO<sub>2</sub> (SISTADOX), Ag/ZnO (DODURIT ZnO)<br />
*Carrier materials Trägerwerkstoffe <br />Cu, CuZn, CuSn et alu.a.<br />
*Quality criteriaQualitätsmerkmale, dimensions and tolerances Abmessungen und Toleranzen <xr id="fig:Quality criteria dimensions and tolerances"/>
<figure id="fig:Quality criteria dimensions and tolerances">
[[File:Quality criteria dimensions and tolerances.jpg|right|thumb|Quality criteria dimensions and tolerancesQualitätsmerkmale, Abmessungen und Toleranzen]]
</figure>
=== Seam–Welded Contact Strip Materials (FDR–Profiles)===