Gold Based Materials

Pure Gold is besides Platinum the chemically most stable of all precious metals. In its pure form it is not very suitable for use as a contact material in electromechanical devices because of its tendency to stick and cold-weld at even low contact forces. In addition it is not hard or strong enough to resist mechanical wear and exhibits high materials losses under electrical arcing loads. This limits its use in form of thin electroplated or vacuum deposited layers.

For most electrical contact applications gold alloys are used. Depending on the alloying metal the melting is performed either under in a reducing atmosphere or in a vacuum. The choice of alloying metals depends on the intended use of the resulting contact material. The binary Au alloys with typically <10 wt% of other precious metals such as Pt, Pd, or Ag or non-precious metals like Ni, Co, and Cu are the more commonly used ones (Table 2.2). On one hand these alloy additions improve the mechanical strength and electrical switching properties but on the other hand reduce the electrical conductivity and chemical corrosion resistance (Fig. 2.2) to varying degrees.

Under the aspect of reducing the gold content ternary alloys with a gold content of approximately 70 wt% and additions of Ag and Cu or Ag and Ni resp., for example AuAg25Cu5 or AuAg20Cu10 are used which exhibit for many applications good mechanical stability while at the same time have sufficient resistance against the formation of corrosion layers (Table 2.3). Other ternary alloys based on the AuAg system are AuAg26Ni3 and AuAg25Pt6. These alloys are mechanically similar to the AuAgCu alloys but have significantly higher oxidation resistance at elevated temperatures (Table 2.4).

Caused by higher gold prices over the past years the development of alloys with further reduced gold content had a high priority. The starting point has been the AuPd system which has continuous solubility of the two components. Besides the binary alloy of AuPd40 and the ternary one AuPd35Ag9 other multiple component alloys were developed. These alloys typically have < 50 wt% Au and often can be solution hardened in order to obtain even higher hardness and tensile strength. They are mostly used in sliding contact applications.

Gold alloys are used in the form of welded wire or profile (also called weldtapes), segments, contact rivets, and stampings produced from clad strip materials. The selection of the bonding process is based on the cost for the joining process, and most importantly on the economical aspect of using the least possible amount of the expensive precious metal component.

Besides being used as switching contacts in relays and pushbuttons, gold alloys are also applied in the design of connectors as well as sliding contacts for potentiometers, sensors, slip rings, and brushes in miniature DC motors (Table 2.5).

Mechanical Properties of Gold and Gold Alloys

Table 2.3: Mechanical Properties of Gold and Gold-Alloys

Table 2.1: Commonly Used Grades of Gold

Table 2.2: Physical Properties of Gold and Gold-Alloys

Fig. 2.2: Influence of 1-10 atomic% of different alloying metals on the electrical resistivity of gold (according to J. O. Linde)

Fig. 2.3: Phase diagram of goldplatinum

Fig. 2.4: Phase diagram of gold-silver

Fig. 2.5: Phase diagram of gold-copper

Fig. 2.6: Phase diagram of gold-nickel

Fig. 2.7: Phase diagram of gold-cobalt

Fig. 2.8: Strain hardening of Au by cold working

Fig. 2.9: Softening of Au after annealing for 0.5 hrs after 80% cold working

Fig. 2.10: Strain hardening of AuPt10 by cold working

Fig. 2.11: Strain hardening of AuAg20 by cold working

Fig. 2.12: Strain hardening of AuAg30 by cold working

Fig. 2.13: Strain hardening of AuNi5 by cold working

Fig. 2.14: Softening of AuNi5 after annealing for 0.5 hrs after 80% cold working

Fig. 2.15: Strain hardening of AuCo5 by cold working

Fig. 2.16: Precipitation hardening of AuCo5 at 400°C hardening temperature

Fig. 2.17: Strain hardening of AuAg25Pt6 by cold working

Fig. 2.18: Strain hardening of AuAg26Ni3 by cold working

Fig. 2.19: Softening of AuAg26Ni3 after annealing for 0.5 hrs after 80% cold working

Fig. 2.20: Strain hardening of AuAg25Cu5 by cold working

Fig. 2.21: Strain hardening of AuAg20Cu10 by cold working

Fig. 2.22: Softening of AuAg20Cu10 after annealing for 0.5 hrs after 80% cold working

Fig. 2.23: Strain hardening of AuCu14Pt9Ag4 by cold working

Fig. 2.24: Precipitation hardening of AuCu14Pt9Ag4 at different hardening temperatures after 50% cold working

Table 2.4: Contact and Switching Properties of Gold and Gold Alloys

Table 2.5: Application Examples and Forms of Gold and Gold Alloys

References

References