Open main menu

Electrical Contacts β

Changes

Test Procedures for the Communications Technology

253 bytes added, 22:03, 21 September 2014
no edit summary
==<!--13.3 -->Test Procedures for the Communications Technology==
Testing of the contact behavior in the communications technology is usually performed on the actual devices such as for example in relays. Experience has shown that the interaction between all design and functional parameters such as contact forces, relative movement, and electrical loads, are determining the failure mode. Therefore only statistical performance tests on a larger number of switching devices lead to meaningful results.
One must differentiate between static tests (for ex. contact resistance) and dynamic ones (for ex. electrical life). In certain electromechanical components and switching devices the contacts can be exposed to both, static and dynamic stresses (for ex. connectors, relays, switches, pushbuttons, circuit breakers). For statically stressed components the life expectancy is usually expressed as a time period, i.e. hours, while for dynamically stressed ones the expected functional life is defined as numbers of operations or switching cycles.
===<!--13.3.1 -->Measuring of Contact Resistance===
The contact resistance in the new stage is for most contact containing electromechanical components a characteristic defining their quality. It is
defined in most standards and acceptance specifications of users. It is important however that a clear definition of the test conditions is given with the specification.
The standard IEC DIN EN 61810-2 defines the application areas of relays according to their load application categories (CC) <xr id="fig:Schematic describing the contact load categories"/> <!--(Fig. 13.5)-->. The categories CC1 and CC2 are separated by the arc-limiting graph (DC breaking capacity). Switching operations below the graph do not generate electrical arcs, those above the graph are accompanied by electrical arcing.
*CC1 is characteristic for switching operations in control circuits at low voltages, for ex. SPS input signals
</figure>
===<!--13.3.2 -->Life Testing===
Electrical life is defined as the number of operations under a defined load (make under load current, current carrying, breaking the load current). The total sequence of this switching cycle leads for the specific design parameters of a relay (bounce characteristics, materials, etc.) to the phenomena responsible for the later device failure, such as increased contact resistance, material transfer, arc erosion, and contact welding, for example <xr id="fig:Relation between the breaking currents of relays and electrical life requirements of switching systems"/> <!--(Fig. 13.6)-->.
As experience shows, failures during load switching are usually related to deterioration of the contact parts. Therefore the mechanical life must always be higher than the electrical life under the required load conditions. Typically the mechanical life is about 10 times higher than the electrical one.
===<!--13.3.3 -->Criteria for Functional Life===
In the communications technology the functional life criteria for switching devices, following conventional standards and specifications are:
Because of this an exact definition for the failure mode must be provided. In most cases the first failure occurrence is defined as the overall device failure, since relays are increasingly used in safety related electrical circuits. Failures to open because of contact welding must be very critically examined. In some instances a weak weld or “sticking” of the contacts can cause a delayed opening and separation of the contacts by themselves. Therefore it is useful to define weld failures as non-opening after a specified time, approx. 1 sec, after the actual switching-off event.
===<!--13.3.4 -->Determination of Functional Life===
Electrical life, failure rate, and reliability are statistical measures. To determine the electrical life the relays are switching the specified load in an accelerated way with higher switching frequency until the first pre-defined failure occurs. The number of switching operations reached for the representative sample size of relays is determined through statistically valid test setups using Weibull distributions. For all switching operations the failure criteria must be monitored and recorded.
</figure>
The large quantity of data generated during the tests can be only analyzed with computer based test systems. After all the relays failed a failure statistic is calculated and the expected electrical life is calculated based on the specified switching and operating criteria. <xr id="fig:Statistical evaluation of the electrical life of relays"/> <!--(Fig. 13.7) --> shows in form of a Weibull diagram the results of a relay life test for a sampling of switching relays under a resistive AC load with failures after the first and the 10<sup>th</sup> occurrence analyzed. From such electrical life test it is also possible to statistically predict the failure rate of relays under certain specified load conditions.
===<!--13.3.5 -->Testing Technology===
The test set-ups for relay tests consist of a load part, which allows the selection of specific electrical loads, and a control / monitoring part, which typically includes the measuring devices with data collection and mostly also a computer for data analysis <xr id="fig:Principle and sequence of testing with electronic load simulation"/> <!--(Fig. 13.8)-->. Variations for testing of different relay types concern mostly the load circuits, the sample size of test specimens, and the frequency of testing.
*Signal Relays (Low Current Relays)
*Automotive Relays
For these relays electrical life tests are conducted under the DC voltage used in the on-board circuitry. Since no standardized tests have been established for automotive relays, the electrical loads are agreed upon between the supplier and the end user. The multitude of load conditions, i.e. resistive, inductive motor, and lamp loads require a flexible set-up of suitable test equipment (see <xr id="fig:Principle and sequence of testing with electronic load simulation"/> )<!--(Fig. 13.8)-->.
During accelerated life tests the following parameters from real life loads must be observed:
These requirements lead to the need to simulate the real life loads through electronically controlled load circuits. Such computerized electronic load circuit simulations easily allow the test sequences to be controlled and monitored:
<figure id="fig:Automotive relays under motor load">[[File:Automotive relays under motor load.jpg|right|thumb|Automotive relays under motor load: Results of electrical life testing using different contact materials]]</figure>
* Time saving test runs for lamp loads by reducing interval times Monitoring of each switching operation for electrical life criteria Allowing to recognize non separation of the contacts after a pre-set time limit to be classified as a relay fallure
Results of relay life testing using different contact materials are illustrated as an example in <xr id="fig:Automotive relays under motor load"/> <!--(Fig. 13.9)-->. For each contact material 10 relays were tested under the prescribed motor load until a failure due to non-opening was detected. For this specific load condition AgNiO. 15 was found to be the best suited contact material.
===<!--13.3.6 -->Failure Analysis=== The full clarification of causes for switching device failures, for example relays, is most important for quality assurance. As a starting point the full history of the relay, such as electrical load, environmental conditions, etc. must be recorded. The process flow chart in Fig. 13.10 clearly describes a proven way to conduct a failure analysis. Fig. 13.10:Flow diagram forevaluation of failurecause in switchingdevices forcommunicationstechnology
The full clarification of causes for switching device failures, for example relays, is most important for quality assurance. As a starting point the full history of the relay, such as electrical load, environmental conditions, etc. must be recorded. The process flow chart in <xr id="fig:Flow diagram for evaluation of failure cause in switching devices for communications technology"/><!--(Fig. 13.10)--> clearly describes a proven way to conduct a failure analysis.
<figure id="fig:Flow diagram for evaluation of failure cause in switching devices for communications technology">
[[File:Flow diagram for evaluation of failure cause in switching devices for communications technology.jpg|right|thumb|Flow diagram for evaluation of failure cause in switching devices for communications technology]]
</figure>
Following all procedures of such a failure evaluation carefully, the root cause of the defect can most likely be established in order to implement preventive measures limiting future occurrences.
==References==
[[Testing Procedures#References|References]]
 
[[de:Prüfverfahren_in_der_Informationstechnik]]